• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window can be a nuisance. It could be a chance to upgrade your windows to energy efficient or insulated ones and enjoy benefits like increased comfort, higher resale value and reduced utility costs.

You can do it yourself at only a fraction of the cost it would cost to employ an expert. It requires the right equipment and an hour or two of your time.

Glass

Replace your single-paned windows using tempered or insulate glass to improve energy efficiency, cut down on noise, and preserve the historical integrity of your home's older. The process of replacing the window pane is easy and can be accomplished by homeowners with basic hand tools. Alongside a replacement sash windows cost pane, the following items are needed for the replacement glass for a window process: latex glazing putty pliers, glazier's points and an electric heater to warm the old putty, if necessary. Before starting, wear gloves and safety goggles as working with broken glass could cause injuries.

Begin by removing any remaining broken pieces of glass. It is recommended to use pliers for this however a flathead could work equally. Then, use a wooden chisel or putty knife remove the remaining old putty around the frame and the sash. Be careful to not break the window sash. Be careful and slow. It is a good idea to work on a sturdy ladder instead of the ground, and to have someone standing below the sash in order to help hold it in place.

Once you have removed all of the old putty, prepare the window frame to accommodate the new pane. Measure the width and height of the opening for the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be taken to a hardware or home center store to have an item cut from stock glass to the right size. Alternately, you can cut the glass yourself if you have the tools you need.

After installing the new glass Apply a small amount of caulking on the edges. This will make the glass weatherproof. Then, you can install a glazier's pointing on each side of the frame to secure the pane into place. The points shouldn't be tight enough to create friction between the frame and the sash however they should not be loose.

Before applying the putty to the surface, gently knead it until it is soft and free from lumps. Cut it into pencil-sized pieces. Apply the first strip to the corner of the frame. Work from one corner to the next and ensure that it is even and smooth.

Glazier's Points

The glazier's points are the small triangular pieces that allow glass to be secured into the frame of a window without damaging or scratching the delicate surface. Knowing how to use these tiny pieces of help is simple and can save you money on professional installation or the cost of purchasing new glass.

Once the old putty and the glazier's point are gone Clean the frame thoroughly with a knife to eliminate any remaining traces. If necessary it is necessary to lightly sand the wood along the grooves of the rabbet to smooth rough spots. If you sand wood, protect it with painter's tape to avoid accidental damage.

Take measurements of the empty frame and record precise measurements. These measurements can be taken to an hardware or home centers store, and the new frame will be cut a bit smaller. This will ensure that the pane fits snugly and allows for expansion and contraction.

Place the new pane into the frame and push firmly using your hands. Utilize the chisel's point, or the back of the putty blade to tap the glazier's points, as illustrated in Figure 11. When you're done taping, they should be in line with the top edge of the pane, and the raised shoulders of the points should be below the lip of the rabbet groove.

Apply a thin layer glazing compound on the rabbet grooves and the edges of the glass. This will protect and seal the edges. Allow this to dry and cure fully.

After the glazing compound dries it's time to put in the new window sash. The first step is to coat the wood with a thick layer of linseed. This will stop the new putty from drying out or cracking when it absorbs moisture. Use a brush to apply this coat, or the tip of the blade. Then use the chisel that is on the back of the putty tool or the back of the handle to gently hammer the new sash or glazier's point into rabbet grooves. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball thrown or a rock thrown by error or a branch falling can cause a broken or cracked window. The majority of windows can be replaced by installing a new piece. The glass is held in place using a small metal clip called a glazier's point and putty, often called glazing compound. Remove the old pane and clean the area using the rag, a pull-type scraper or wood chisel. Wear safety glasses and gloves when you work. If the window is secured to the frame, you'll need to employ a heat gun in order to soften the adhesive before prying it free.

If you are planning to replace the original sash in the future, take care to remove any pieces of molding that secure the old pane. Then you can sand the sash down to make sure it's flat and ready for a new caulk. Once the sash is put back in place it is possible to apply a silicone caulk on the glass. This will ensure that it won't leak over time or discolor.

Remove the glazing points in the rabbets. These are the grooves on the sash where the glass is. If they're hard to chisel out, try placing an instrument like a heat gun to soften them before you do. When using a heat tool, make sure to not damage the sash or its railings.

Prepare the bed for your new pane by removing the old glaze and putty. Roll a rope made of glazing compound between your fingers, and then make it about 1/2 inch thick. Then, you can press it into the rabbets in which the glass will sit. The Glass For windows replacement must rest against the putty on both sides. If you need to, lightly tap your glass into the rabbet with your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk before pressing it into the sash. If not, you'll have to apply putty over the crack to form a tight seal and keep water out. After the putty is dry, clean the oily film off the glass with the help of a rag. Allow it to dry completely prior to painting. If you paint before the putty is completely dry, it won't create an effective seal and could be leaking or discoloring in time.

Paint

If you've had a broken window pane, you might be worried about the expense of replacing it. But the truth is that replacing one glass pane does not require a huge amount of money If you can do it yourself. In fact even windows with double panes can be replaced for only a fraction of the cost of a professional.

If you are working on a large window, make sure it is securely fastened to the frame. Using the proper tools and techniques you can make this task relatively easy and speedy.

When you're ready to start, begin by removing the old window pane by removing the glazing points of metal that are attached to it. These are basically small metal triangles that act as "nails" that hold the window in place in the wood frame. They are buried beneath a bead or glazing putty that sets to form solid wedge that holds the frame firmly in position and conceals the edges.

After removal of the old pane clean the frame and the wood. Scrape off any paint that has been used and sand the rabbet grooves in which the glazing points were placed. These should be sanded to the point of being bare, to allow you to paint them the same color as the rest the frame. After sanding, apply a coat of flax oil to the wood that is not sanded down to prolong its life.

Next, measure the dimensions of the window's opening. You will need to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get a precise size for the new pane. This will also allow for expansion and contraction of the glass during seasons of changes. Take these measurements to the hardware or home improvement store, and they will have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.