• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen can maneuver large glass panes from a high point above the ground. They work in extreme weather conditions and follow strict safety protocols.

Wearing protective clothing, take off the metal glazing points as well as all glazing putty using an utility knife. A heat gun can help to soften and take off the old putty.

Replacement

When a window pane breaks, it can be tempting to try and repair the glass rather than replace it. It is more cost-effective to replace a window, and it can also help you to avoid other issues in your home's efficiency. Consider the kind of glass damaged to determine whether it's a temporary fix, or if a long-term solution is needed.

To fix a broken window, you must remove the frame or sash and place it flat on your work surface. Wearing eye protection, gently move the window's frame and remove any remaining fragments. Utilize a utility blade to remove the glazing compound, as well as the glazing points that secure the window. Keep the track of these components and their locations to ensure that they can be reinstalled later.

After removing the frame and sash you can begin preparing to replace the glass. Make sure that the opening of the frame is the right size for the replacement window. To allow for the expansion of the frame and glass and contraction to both directions, measure the opening and subtract 1/8 inch. Then, you can purchase double-strength glasses that are cut to these exact dimensions. It is a good idea also to purchase enough glazier's clips or points to be installed every 6 inches around each window pane.

If the manufacturer is responsible then you should call them and file a claim. Once the new glass has been installed, it should be covered with a thin coating of the compound used by glaziers. After the compound has dried, you can paint it to match the rest of the window frame.

If your crack is more than an inch in length you can stop it from expanding by slicing an arc that is just a little beyond the crack. This trick won't be foolproof, but it can slow the development of the crack to a manageable size until you can take more permanent measures.

Repair

Professional window installers have the proper tools and know how to work with various types of glass. They know how to dispose of waste safely which means they are less likely than other contractors to leave behind pieces of glass which could cause harm to family pets or family members. They are also experienced in working with different kinds of windows, and may be able to spot problems that a novice home owner might not see.

Before you begin the process of repairing damaged window glass, be sure to wear safety glasses and gloves. Even a small crack can cause shards of glass to fly and could pose a danger to anyone inside or around the house. It is important to determine the cause of the crack, since this can prevent future issues.

Start by making an epoxy mixture that has two parts. They usually consist of composed of a 50/50 blend of hardener and resin. They must be mixed quickly. Once the mixture has been prepared and applied, simply apply it to the crack and let it dry. It will take just some minutes, but you must be quick because the mixture is extremely thick and will dry quickly.

After the epoxy has dried, you can take off any excess with a putty knife. The next step is to clean around the cracked glass. If you don't clean the area in a proper manner, the debris could cause further damage to the glass. Use a putty blade smooth out the compound around the edge of your window and then match it to the frame of wood.

To make a more durable option, consider using a plastic covering. You can cover the glass using masking tape or a sturdy trashbag. This will prevent the crack from expanding and will also keep out wind, water, bugs, and debris.

If you're unable to reach the window in a timely manner, you can use silicone sealant to make temporary repairs. Apply a small amount silicone sealant on the edge of the damaged glass. It won't fully seal the gap between glass and frame however it will keep the crack in place while you fix it.

Repainting

If your glass windows are old, you might need to paint them. This is a cost-effective alternative to replace windows and give your house a new appearance. Before painting, ensure that the surface is clean. Clean the window with water and soap or ruby alcohol to get rid of oil smudges and other traces which can hinder the paint from adhering. Wear rubber gloves when working on glass surfaces to avoid the transfer of oils from your fingers onto the surface. Apply multiple thin coats instead of just one large coat. This will help the paint last longer, and keep your windows looking smooth and even.

Make sure you have the proper tools available when you are planning to repaint glass windows. You will need either a brush or sponge, painter's tap along with a ruler, toothpicks and a ruler. You should have the paints and brushes that you will be using on hand. Be sure to follow the manufacturer's instructions and be prepared with plenty of patience since it may take awhile for the paint to dry.

It is also important to ensure that the area you're working in is ventilated when you're using solvent-based paint. This will decrease the chance of inhaling toxic chemicals, and also the paint will dry faster. You should also make sure you have a protective mask for any spray paints you use.

For older glass windows, you'll need to prepare the surface prior painting. Clean the glass thoroughly with soap and warm water. Then, apply rubbing alcohol to wash away any grease or oil that could hinder paint's adhesion. Make sure the windows are completely dry prior to coating them.

If you have energy-efficient double glazed repair pane windows on your windows, it might be possible to submit an insurance claim for repair double glazed window or replacement with the company that makes the windows or dealer that sold them. This is particularly true if the windows are still under warranty and have experienced several problems with condensation or broken glass.

Sealing

Whether you have old double-pane windows with damaged seal or more recent insulated glass units (IGUs) that have experienced fogging, there are several methods to fix the issue. The most expensive option is to replace the frame and insulated unit, but it may be necessary if condensation or fog cause energy loss. Other alternatives include replacing the current IGU with a single-pane, or repair it by drilling a small hole in the bottom of the unit and then filling the solution with anti-fog.

You can also seal up the gap between a window frame and a threshold or sill with a felt strip or vinyl v-strip. Felt is affordable and can be fixed with glue, nailed or stapled to the frame, but it does not offer much protection against moisture. Vinyl weather stripping v-strip is durable and simple to install, but it is costly and is typically reserved for areas that are exposed to abrasions that are high. Door sweeps are able to be easily nailed to the floor and are affordable. However, they provide little or no protection between the threshold and the air.

To fix a damaged window seal, use a putty blade to scrape off the caulk. Wearing eye protection and gloves take care to remove the glazing points -- tiny fasteners that hold the glass in the frame's recess using sharp edges and pointed edges. Once you have removed the glazing points, clean the grooves and sand the wood to a smooth finish. Wipe off any sanding debris, then seal the bare wooden surface with a linseed-oil-based paint or clear sealer.

Traditional glazing putty can be applied with the help of a putty blade or caulking gun, however a knife provides a better application that is more precise and creates a better seal. Choose a putty that is made specifically for glass windows as it has better adhesion and durability.

Apply a small amount of the putty to the inside edge of the frame where it meets the glass. Slide the window into the frame so that scribed line on glass aligns with the frame's edge. Apply pressure to the glass in order to force the putty to form a tight seal. Smooth the compound using a gloved finger, and wipe away any caulk that was applied incorrectly or spills that are not properly wiped away before it dries.